Saturday, May 25, 2013

17 Distaff View



So, what does Suzanne think about all this? The following pages are copies of a four page brochure that she did as an Adobe class assignment years ago.
 


 
 

 
 


 
 
I especially like the subtle logo in the upper left corner of the last page.

Thursday, May 23, 2013

16 Let There Be Light





The coupe does not have power steering and it had a 13" diameter Grant steering wheel. It steered alright on the road, but it was a really difficult to turn the wheel when it was not moving. Since I have entered my eighth decade and might not be quite as strong as I was when I installed the Grant wheel, my wife decided to buy a Limeworks reproduction '39 banjo steering wheel for my 71st birthday. These wheels are 17" diameter like the originals.

The steering wheel looks great but felt a little loose on my (stock) column. I was able to shim it with electrical tape between the column and key and the wheel hub. The steering effort at rest is much better than before. It's amazing what four extra inches can do.

However, the distance between the steering wheel and the brake pedal was reduced enough so that it was difficult to get my foot on the brake pedal. I did several things to address this. First I adjusted the pedal return spring so that the brake pedal was even with the clutch pedal. Then I made brackets to move the seat down and back. The clearance between the pedal and wheel was better, but I still worried about being able to stop in an emergency situation.
Since the steering column drop is about 1" shorter in a '40 than a '39, and since a stock '40   drop is damn near as ugly as a '39, I decided to use a custom '40 style drop from SoCal Speed Shop. Since I didn't like the polished appearance, I had it powder coated gloss black to blend in with the dash. I also got a 4' piece of 1½" x .035 wall chrome-moly tubing to replace the thick wall chrome-moly tube we used when we suspended the brake pedals from the steering column years ago. The supplier was OnLineMetals. I cut the tubing to length (41⅜") and had it powder coated gloss black.
While I was making changes in the steering column area, I decided to address another safety related issue. The horn button was the old starter button and I had to think a moment to realize where it was. I wanted to put the horn button back in the center of the steering wheel.
           From Model A (1928) through 1939 V8s, Ford's "better idea" for the horn and headlight
           wiring was to have the switch body mounted at the base of the steering column. The '39
           switch wiring looks like this:


The four wires shown in bold type were routed to the American Autowire panel under the dash. The remaining three wires are for functions already included in the panel and are therefore not necessary.
I bought a used stock '39 headlight switch, horn button and light switch rod, brass guide, bottom plate and light switch mount for the steering column. Hot Rod building axiom #3 - Don't ever sell or throw anything away that is in any way related to your car. If you need it in the future it's likely to be very expensive. Of course, this axiom is likely to put a strain on your marriage. It can be worked out though. My first marriage lasted 30 years, until my wife died. My second marriage is still strong after 18 years. If you treat her right, she will put up with the hot rods. The sermon is over.

In order to use the horn button in the center of the steering wheel, I needed the light switch assembly and wiring harness. These parts were purchased from Bob Drake reproductions. The switch housing was made of thinner metal than the original and the tines that hold the two pieces together are smaller than they should be. The result is that the rear piece is not secure enough to hold the rear half of the light switch in place. I had to use a hose clamp to squeeze the front half of the housing so the two pieces together and shim the switch plate contact piece with two layers of electrical tape so that it would not tilt in the housing. It is really tricky to assemble the switch correctly.

In the center of the horn button rod is a wire which is insulated from the rod itself. When it is depressed, the horn button touches the top of that wire, grounding it, There is a contact in the center of the light switch which should have a spring behind it so that it touches the lower end of the insulated wire and transfers the ground to the horn relay which blows the horn. None of the parts which I bought contained the required spring, and there was no instruction sheet mentioning the spring. So I had to unsolder the wire from the contact, determine how long the spring needed to be, buy a spring of the required diameter and length, install the spring and contact and resolder the wire to the contact. Also it is a very good idea to check the continuity of the insulated wire before reassembling the steering column. Of course, I did not do that.

Checks - button on light switch end of horn rod to horn rod - insulated
               horn rod button to ground - insulated
               rod button with horn button pressed - grounded
               horn rod button to ground with steering wheel turned lock to lock - insulated

The insulated wire is continuous. However, instead of not sounding at all. the horn sounded all the time whether the key is on or off. The lower contact is isolated from ground .

I tired of trying to make the Drake parts work. I got a hold of a genuine '38 Ford harness and used parts of it to mate with the Drake parts. This required buying a '38-'39 bail and continuing use the hose clamp to hold the housing together. When I reconnected the battery and removed the 9V temporary, the lights and the horn worked properly. I never did identify the ground.

The dash lights only operated when the old headlight switch was activated. Since the parking light contact was on whenever the taillights were, I ran a wire from there to a stock rheostat. The other side of the rheostat was connected to the dash lights. The dash lights then worked with the new stock headlight switch and could be dimmed or turned off when desired.

 

 

horn

 
 

 

 

 

 
        


         



Monday, May 13, 2013


15   Photos and Specs                                                       

 

1939 Ford VIN:     18-4951487
Original dealer:     Duryea Motors, Somerville, NJ
Date of Sale:     August 16, 1939
Buyer:     John N. Alpaugh
License Number:     NA 14 A (NJ-1939) – transferred
Traded in:     To F. Day Ford, Plainfield, NJ on a 1960 Ford in 1959
Mileage at trade-in:     38,000 miles
Purchased by:     Elmer R. Bollenbach for his son Charles
Purchase date:     October 19, 1959
Purchase price:     $400 + 1950 Studebaker 4 door sedan ($95.00)
Family transfer:     December 1, 1966
Registrations:     Unknown number transfered from 1950 Studebaker
                         ATY 765 (NJ), QQ-Q 9 (NJ historic),
                         6G13-81 (NY year of manufacture historic plates),
                         981-EPJ (NV), 00609 (NV - UNLV plates)
                         678-GKP (CO collector vehicle plates)
Body:     1939 Ford Deluxe Coupe
Modifications:     124 Hood louvers
                          cat whiskers & lower side spear removed from hood 
                          Ford Deluxe script removed from hood
                          Ford script removed from deck lid
                          Bob Drake halogen headlights
                          Wescotts front and rear fiberglas fenders
                          1940 Ford trunk handle
                          1940 Ford “swan’s neck” side mirrors
                          1939 Ford “Blue Dot” taillight lenses
                          Bob Drake 1940 Ford front bumper and
                          '40 Ford rear bumper with Ford script 3rd brake light
Paint:     1997 GM (Saturn) Purple Poly Urethane
           

Front suspension:     1954 Chevrolet
Front brakes & rotors:     1968 Corvette w/ stainless steel sleeved calipers
Master cylinder:     1970 Corvette w/o power brakes
Frame:     1939 Ford with altered crossmembers
Steering box:     1939 Ford
Steering column:     1939 Ford with chrome moly tube shaft
Front springs:     1956 Corvette with one coil removed
Front Shocks:     1962 Corvette
Front wheels:     GM Code DC 15 x 6 ('67 Corvette, '67-'70 Passenger)
Front tires:     BF Goodrich Comp T/A 195/60 HR 15 M&S
Rear suspension:     1968 Corvette
Rear brakes & rotors:     1968 Corvette w/ stainless steel sleeved calipers
Rear End Ratio:     3.70:1
Rear spring:     1968 Corvette with 2 leaves removed
Rear wheels:     GM Code AG 15 x 7 ('68 Corvette)
Rear tires:     Goodyear Wingfoot HP P225/70R15
Engine:     1964 Buick Riviera 425 ci Engine # 7K1082768 Code KW 31
Piston oversize:     .030”
Intake manifold:     Polished Offenhauser 360ยบ “Equa-Flow” 2 x 4 bbl
Carburetors:     Two Edelbrock 1404 500 cfm
Camshaft:      Kenne-Bell Mk C-118
Ignition:     1964 Buick distributor Pertronix Ignitor Ignition System
Flywheel:     1964 Buick
Clutch:     Centerforce Dual Friction #DF735552 (‘70-’74 Corvette 454)
                QuarterMaster QTR 720100 Hydraulic Throwout bearing
Trans:     Muncie M-22 Four Speed with Doug Nash Cast Iron Case
              Gear Vendors Under/Overdrive   
 
 



Saturday, September 15, 2012

14 Interference (Parts 2 and 3)


Since I believe that the worst thing that you can do to a vehicle is to not drive it regularly, I try to drive the hot rod to work at least once a week.

On one of these trips, I heard a loud snap, then the engine started to backfire through the carburetor under load. By removing one plug wire at a time, I was able to determine that the problem was in number three cylinder. When I removed the valve cover, I found that the exhaust rocker arm on #3 was broken in half.

 I bought three rocker arms (two of Egge Machine # 44000, the type that broke, and one #44001).  One was hand filed for clearance as mentioned in Chapter 9, installed on the right rocker shaft, and reinstalled on the engine. (Nailhead Buick cylinders are numbered  1, 3, 5, 7 on the right bank and 2,4,6,8 on the left.)
 
Less than 1,000 miles later, the #3 exhaust rocker arm broke again.
Less than 500 miles later, the #3 exhaust rocker arm broke a third time.
Thinking that the problem was that the rocker was hitting the edge of the (larger diameter) Kenne-Bell valve spring retainer, I decided to keep the Kenne-Bell cam, but install a stock head on the right bank until I was able to determine how to fix the problem.

 I found a stock 425 head with rocker assembly at Wheatbelt Antique Auto, a Buick specialist in Carrier, OK. When it arrived, the UPS driver was the first and only delivery person to acknowledge the sign in the empty planter along side of the front porch which read "Please place deliveries here". I had to reach down two feet into the clay pot and lift the heavy sucker out of there. After that ordeal, installing it on the right side of the engine was relatively easy. For nearly three years, there have been no further problems with the right bank valve train.
Recently the engine developed a miss and an intermittent tick on the left side. Because I don't know all of the peculiarities of Nailhead Buick engines, I decided to find  someone who had experience building them to see if we could find a permanent fix.  Most of the builders I talked to had never worked on a Nailhead.
Ryan at Ryan's Rod Service said he had some experience with Nailheads, and he knew an expert to go to if he ran into trouble.   
                  
I asked him to degree the cam at 113°ATDC ± 1° per the cam card and check out the miss problem . (The cam was originally installed straight up at 118°ATDC, 5° retarded from where it should have been.)
This engine was built following  the 1997 series of articles in Street Rodder written by Doc  Frohmader. There was an error in Part 6 (June 1997) describing advancing the cam to the 2A marks. However, the particular and peculiar crankshaft gear that we both used is marked in camshaft degrees, not crankshaft degrees. The cam should be advanced to the 4A marks. On page 60 of the magazine, the photo caption on the left hand photo is correct.
A minor problem cropped up when reinstalling the timing cover. The original rope  front crankshaft seal and stamped  steel retaining ring  had been removed and replaced with a more modern nitrile lip type seal sourced  from Carmen Faso at  J&C's Parts in North Tonawanda, NY. Carmen is not on the internet. TA Performance in Scottsdale, AZ  lists a neoprene seal part number TA 1514 but that number does not cross to any other manufacturer. The source article did not mention an application. A little digging on http://www.v8buick.com  revealed that a National 474272 seal, an SKF 19786 seal or a Chicago Rawhide 19786 seal will work. I still don't know the application. Getting this solved took way more time than it should have.
After correcting the cam to crank timing, Ryan removed the left valve cover and discovered a broken rocker arm on number two intake valve. According to his sources, Nailheads with non-stock cams break rocker arms because of incorrect valve train geometry. That makes sense because of the complexity of the valve train. However, they said that the rockers will break when the pushrods are too short, which is counterintuitive.
Ryan installed one of the filed  rocker arms from  the modified head  I had removed from the right side. The pushrod was reused. If another rocker arm breaks, the plan is to order Smith Brothers adjustable pushrods and install them with the adjustment end near the lifter (upside down) for easier adjustment. The intake manifold and valley cover will need to be removed to adjust them, but it should only have to be done once.
 

Wednesday, July 4, 2012

13 Sounds


I was recently reminded of a chapter of the coupe history that happened ten years ago.

For Fathers' Day of 2002, Suzanne asked me if I Wanted a stereo for the hot rod. I said that I did,so we went to Car Toys to listen to their demo systems. As much as I love music, my hearing is not good enough to tell the difference between entry level and top quality sound. We settled on a Pioneer receiver, amplifier and 6 CD changer.

The salesman was a kid in his late teens. I described the business coupe and told him that there was no room for any of the equipment anywhere except behind the seat. He tried to listen to me, but it was clear from his glazed eyes and fidgiting that he had no clue what I was saying. He suggested that we look at the car. As we were walking toward it, he said "It's not a Honda. I don't know what to do with it." He went back inside the store and got an installer who knew where to place the units and speakers.

When the installation was done, the technician could not get the remote to work except by aiming it under the seat directly at the receiver. I returned the signal relay and kept the stereo. After all, changing the station was no more distracting than dialing a cell phone.

I later mentioned the problem to a salesman at SoundTrack. He tod me that home remote stereo systems operate on 12 volts. I said "Oh, do they?' and asked what I would need to use a home system in a car. I bought a single zone IR repeater system, a minisensor and a micro flasher. When I installed it, the system worked but the flasher beam was too narrow for reliable use in a car. I traded the flasher for a larger unit and the system has worked flawlessly ever since. The stereo remote is Velcroed to the car seat and aimed at the sensor under the dash. The sensor sends a signal by wire to thr repeater which operates the flasher aimed at the stereo.

Rube Goldberg yes, but I havent rearended anyone while changing CDs.




Wednesday, April 11, 2012

12 Disengagement (Part 2)

Although the realization might come a little late, I usually figure out when it's time to hire professional help.

The first time the coupe went to a local shop called "Gasoline Alley", it was running way too rich. The car was built at sea level and the carburetor jetting was way off for operation at 5280 feet. The owner of the shop knew AFBs inside out. When he finished with the carburetors, he claimed that they would pass Colorado emissions testing. They didn't have to because the car is too old, but the man knew how to brag. I will say the coupe ran 100% better.

Early in 2002, the clutch started to go out of adjustment. Each time I adjusted the master cylinder actuating rod, it improved for a few drives, then got worse. Eventually I ran out of adjustment. In four attempts, I spent a total of ten hours trying to vacuum bleed the clutch mechanism with no success.

I had the car towed to Gasoline Alley. They examined the clutch hydraulic system and found it was contaminated with thousands of rubber chunks.

We had used a hose on the remote fill reservoir which wasn't compatible with brake fluid. The brake fluid attacked the inside of the hose and eventually caused it to disintegrate.
Gasoline Alley had to remove the driveshaft, transmission and bellhousing and replace the hydraulic throwout bearing, master cylinder and the connecting hoses. Since we replaced all of the expensive parts, we replaced the reservoir too. This time we used brake hose from the reservoir to the master cylinder.

The second time we drove the car to "Hot Times, Kool Cars" (the annual firefighters car show to benefit Children's Hospital Burn Unit), the bearing in the Corvette left wheel support banjo seized. As much fun as it is to drive the hot rod, it's extremely embarrassing to the leave a car show with your car on the back of a roll back tow truck. There wasn't enough room in the cab to duck down so no one could see us. We took the '39 directly to Gasoline Alley, then rode home in the roll back.

Gasoline Alley didn't have a tool to disassemble the banjo and didn't want to use my homemade one. They sent the part to a Corvette specialist for repair. Shortly after I got the car back, an intermittent clunking sound started coming from the right rear. When they realigned the rear, they didn't get the pivot bolt tight enough. The bolt worked loose allowing the pivot end of the banjo to bang against the mounting bracket.

I fixed this at home, but I learned that it pays to check the work of every shop, even those with a sterling reputation.

Saturday, June 5, 2010

11 Time Travel

The second time I drove the coupe to work, the shifter hung up in second gear. Suddenly, it was 1960. After several bouts with the shifter, I pulled out my 40 year old Hurst instruction sheet and determined that the 1-2 arm and the 3-4 arm were interchanged. The two arms look identical, but they aren't. I swapped the two shifter arms and lined up the neutral gate using an Allen wrench. The shifter has not hung up since.

'39 Deluxe grilles consist of twenty-five separate chrome pieces mounted on a formed and welded sheet metal backing. I banged up the sheet metal piece when I hit a wheel stop in a parking lot. I removed all of the chrome pieces and took the sheet metal part to Masterpiece Rodding and Restoration in Denver. They called me two days later and said the grille was repaired. The bill was $135.00 for three hours work. When I pulled out my debit card, the owner said "I don't take credit cards." I had only $80 with me. He said "Take the grille with you and mail me a check." Another time warp.

When Rustic built the car, they insisted on installing both a puller fan and a pusher fan to make sure the car wouldn't overheat. In practice, I never used the pusher fan. The car never boiled over. Since all the pusher fan was doing was blocking air, I removed it and put it in the spare parts pile. I installed an overflow tank and filled the system with Evans NPG+ coolant. This stuff boils at 369°F without a pressure cap. 50/50 ethylene glycol and water boils at 224° F without a pressure cap. Evans NPG+ does not freeze. At -70° F it contracts slightly and becomes a viscous slurry. It is used full strength, not mixed with water.

With the cooling system changes, I had no overheating problems. However, the temp gauge often indicated 260°. I called United Speedometer who had built the LED stack temperature gauge and determined that the temperature sender on the engine was not the Stewart Warner unit that had been supplied with the gauges. A little more research located a Stewart Warner dealer where I was able to order a sender with the proper thread for the Buick head. When I installed it, the indicated temperature was nearly 30° lower than before. When all else fails read the instructions, even if you're a guy.

One other cooling related issue. At my insistence, the puller fan was wired to a battery feed so that the cooling would continue after the engine was shut off. After several dead battery incidents, I changed the fan power to an accessory lead.

I bought four 15" wheels from Wheel Vintiques and had them powder coated orange. I mounted the tires and put them on the car. The rims hit the Corvette calipers on both the front and rear wheels. The stock Chevrolet wheels I had been using didn't hit. I tried 5/16" thick wheel spacers from JC Whitney to space the wheels out enough to clear the calipers. This caused the tires to rub the fenders on turns. I spoke to Pete Van Iderstine at Early Wheel to find out if their wheels would clear. Pete told me that all of the aftermarket wheel suppliers used the same centers and rims. He suggested grinding the Corvette calipers to clear the wheels. I ground and refit the wheels again and again until they seemed to clear, then went for a test ride. They still hit. So I ground and test drove several times until I didn't hear them squeaking. It was necessary to grind the bleeder on the back calipers so much that it was not possible to bleed the rear brakes. The rear tires still rubbed until I had the Corvette rear adjustment corrected. One of the rear wheels I had been using was an AG code 7" wide rally wheel. These were only used on Corvettes, and only in 1968. I finally found another one, had the two of them powder coated and installed them. I replaced the rear calipers at the same time. I used aftermarket rally wheels on the front. These have the same clearance problem as the solid wheels, so I am still looking for a pair of 15" x 6" GM rally wheels for the front.