Saturday, September 15, 2012

14 Interference (Parts 2 and 3)


Since I believe that the worst thing that you can do to a vehicle is to not drive it regularly, I try to drive the hot rod to work at least once a week.

On one of these trips, I heard a loud snap, then the engine started to backfire through the carburetor under load. By removing one plug wire at a time, I was able to determine that the problem was in number three cylinder. When I removed the valve cover, I found that the exhaust rocker arm on #3 was broken in half.

 I bought three rocker arms (two of Egge Machine # 44000, the type that broke, and one #44001).  One was hand filed for clearance as mentioned in Chapter 9, installed on the right rocker shaft, and reinstalled on the engine. (Nailhead Buick cylinders are numbered  1, 3, 5, 7 on the right bank and 2,4,6,8 on the left.)
 
Less than 1,000 miles later, the #3 exhaust rocker arm broke again.
Less than 500 miles later, the #3 exhaust rocker arm broke a third time.
Thinking that the problem was that the rocker was hitting the edge of the (larger diameter) Kenne-Bell valve spring retainer, I decided to keep the Kenne-Bell cam, but install a stock head on the right bank until I was able to determine how to fix the problem.

 I found a stock 425 head with rocker assembly at Wheatbelt Antique Auto, a Buick specialist in Carrier, OK. When it arrived, the UPS driver was the first and only delivery person to acknowledge the sign in the empty planter along side of the front porch which read "Please place deliveries here". I had to reach down two feet into the clay pot and lift the heavy sucker out of there. After that ordeal, installing it on the right side of the engine was relatively easy. For nearly three years, there have been no further problems with the right bank valve train.
Recently the engine developed a miss and an intermittent tick on the left side. Because I don't know all of the peculiarities of Nailhead Buick engines, I decided to find  someone who had experience building them to see if we could find a permanent fix.  Most of the builders I talked to had never worked on a Nailhead.
Ryan at Ryan's Rod Service said he had some experience with Nailheads, and he knew an expert to go to if he ran into trouble.   
                  
I asked him to degree the cam at 113°ATDC ± 1° per the cam card and check out the miss problem . (The cam was originally installed straight up at 118°ATDC, 5° retarded from where it should have been.)
This engine was built following  the 1997 series of articles in Street Rodder written by Doc  Frohmader. There was an error in Part 6 (June 1997) describing advancing the cam to the 2A marks. However, the particular and peculiar crankshaft gear that we both used is marked in camshaft degrees, not crankshaft degrees. The cam should be advanced to the 4A marks. On page 60 of the magazine, the photo caption on the left hand photo is correct.
A minor problem cropped up when reinstalling the timing cover. The original rope  front crankshaft seal and stamped  steel retaining ring  had been removed and replaced with a more modern nitrile lip type seal sourced  from Carmen Faso at  J&C's Parts in North Tonawanda, NY. Carmen is not on the internet. TA Performance in Scottsdale, AZ  lists a neoprene seal part number TA 1514 but that number does not cross to any other manufacturer. The source article did not mention an application. A little digging on http://www.v8buick.com  revealed that a National 474272 seal, an SKF 19786 seal or a Chicago Rawhide 19786 seal will work. I still don't know the application. Getting this solved took way more time than it should have.
After correcting the cam to crank timing, Ryan removed the left valve cover and discovered a broken rocker arm on number two intake valve. According to his sources, Nailheads with non-stock cams break rocker arms because of incorrect valve train geometry. That makes sense because of the complexity of the valve train. However, they said that the rockers will break when the pushrods are too short, which is counterintuitive.
Ryan installed one of the filed  rocker arms from  the modified head  I had removed from the right side. The pushrod was reused. If another rocker arm breaks, the plan is to order Smith Brothers adjustable pushrods and install them with the adjustment end near the lifter (upside down) for easier adjustment. The intake manifold and valley cover will need to be removed to adjust them, but it should only have to be done once.
 

Wednesday, July 4, 2012

13 Sounds


I was recently reminded of a chapter of the coupe history that happened ten years ago.

For Fathers' Day of 2002, Suzanne asked me if I Wanted a stereo for the hot rod. I said that I did,so we went to Car Toys to listen to their demo systems. As much as I love music, my hearing is not good enough to tell the difference between entry level and top quality sound. We settled on a Pioneer receiver, amplifier and 6 CD changer.

The salesman was a kid in his late teens. I described the business coupe and told him that there was no room for any of the equipment anywhere except behind the seat. He tried to listen to me, but it was clear from his glazed eyes and fidgiting that he had no clue what I was saying. He suggested that we look at the car. As we were walking toward it, he said "It's not a Honda. I don't know what to do with it." He went back inside the store and got an installer who knew where to place the units and speakers.

When the installation was done, the technician could not get the remote to work except by aiming it under the seat directly at the receiver. I returned the signal relay and kept the stereo. After all, changing the station was no more distracting than dialing a cell phone.

I later mentioned the problem to a salesman at SoundTrack. He tod me that home remote stereo systems operate on 12 volts. I said "Oh, do they?' and asked what I would need to use a home system in a car. I bought a single zone IR repeater system, a minisensor and a micro flasher. When I installed it, the system worked but the flasher beam was too narrow for reliable use in a car. I traded the flasher for a larger unit and the system has worked flawlessly ever since. The stereo remote is Velcroed to the car seat and aimed at the sensor under the dash. The sensor sends a signal by wire to thr repeater which operates the flasher aimed at the stereo.

Rube Goldberg yes, but I havent rearended anyone while changing CDs.




Wednesday, April 11, 2012

12 Disengagement (Part 2)

Although the realization might come a little late, I usually figure out when it's time to hire professional help.

The first time the coupe went to a local shop called "Gasoline Alley", it was running way too rich. The car was built at sea level and the carburetor jetting was way off for operation at 5280 feet. The owner of the shop knew AFBs inside out. When he finished with the carburetors, he claimed that they would pass Colorado emissions testing. They didn't have to because the car is too old, but the man knew how to brag. I will say the coupe ran 100% better.

Early in 2002, the clutch started to go out of adjustment. Each time I adjusted the master cylinder actuating rod, it improved for a few drives, then got worse. Eventually I ran out of adjustment. In four attempts, I spent a total of ten hours trying to vacuum bleed the clutch mechanism with no success.

I had the car towed to Gasoline Alley. They examined the clutch hydraulic system and found it was contaminated with thousands of rubber chunks.

We had used a hose on the remote fill reservoir which wasn't compatible with brake fluid. The brake fluid attacked the inside of the hose and eventually caused it to disintegrate.
Gasoline Alley had to remove the driveshaft, transmission and bellhousing and replace the hydraulic throwout bearing, master cylinder and the connecting hoses. Since we replaced all of the expensive parts, we replaced the reservoir too. This time we used brake hose from the reservoir to the master cylinder.

The second time we drove the car to "Hot Times, Kool Cars" (the annual firefighters car show to benefit Children's Hospital Burn Unit), the bearing in the Corvette left wheel support banjo seized. As much fun as it is to drive the hot rod, it's extremely embarrassing to the leave a car show with your car on the back of a roll back tow truck. There wasn't enough room in the cab to duck down so no one could see us. We took the '39 directly to Gasoline Alley, then rode home in the roll back.

Gasoline Alley didn't have a tool to disassemble the banjo and didn't want to use my homemade one. They sent the part to a Corvette specialist for repair. Shortly after I got the car back, an intermittent clunking sound started coming from the right rear. When they realigned the rear, they didn't get the pivot bolt tight enough. The bolt worked loose allowing the pivot end of the banjo to bang against the mounting bracket.

I fixed this at home, but I learned that it pays to check the work of every shop, even those with a sterling reputation.

Saturday, June 5, 2010

11 Time Travel

The second time I drove the coupe to work, the shifter hung up in second gear. Suddenly, it was 1960. After several bouts with the shifter, I pulled out my 40 year old Hurst instruction sheet and determined that the 1-2 arm and the 3-4 arm were interchanged. The two arms look identical, but they aren't. I swapped the two shifter arms and lined up the neutral gate using an Allen wrench. The shifter has not hung up since.

'39 Deluxe grilles consist of twenty-five separate chrome pieces mounted on a formed and welded sheet metal backing. I banged up the sheet metal piece when I hit a wheel stop in a parking lot. I removed all of the chrome pieces and took the sheet metal part to Masterpiece Rodding and Restoration in Denver. They called me two days later and said the grille was repaired. The bill was $135.00 for three hours work. When I pulled out my debit card, the owner said "I don't take credit cards." I had only $80 with me. He said "Take the grille with you and mail me a check." Another time warp.

When Rustic built the car, they insisted on installing both a puller fan and a pusher fan to make sure the car wouldn't overheat. In practice, I never used the pusher fan. The car never boiled over. Since all the pusher fan was doing was blocking air, I removed it and put it in the spare parts pile. I installed an overflow tank and filled the system with Evans NPG+ coolant. This stuff boils at 369°F without a pressure cap. 50/50 ethylene glycol and water boils at 224° F without a pressure cap. Evans NPG+ does not freeze. At -70° F it contracts slightly and becomes a viscous slurry. It is used full strength, not mixed with water.

With the cooling system changes, I had no overheating problems. However, the temp gauge often indicated 260°. I called United Speedometer who had built the LED stack temperature gauge and determined that the temperature sender on the engine was not the Stewart Warner unit that had been supplied with the gauges. A little more research located a Stewart Warner dealer where I was able to order a sender with the proper thread for the Buick head. When I installed it, the indicated temperature was nearly 30° lower than before. When all else fails read the instructions, even if you're a guy.

One other cooling related issue. At my insistence, the puller fan was wired to a battery feed so that the cooling would continue after the engine was shut off. After several dead battery incidents, I changed the fan power to an accessory lead.

I bought four 15" wheels from Wheel Vintiques and had them powder coated orange. I mounted the tires and put them on the car. The rims hit the Corvette calipers on both the front and rear wheels. The stock Chevrolet wheels I had been using didn't hit. I tried 5/16" thick wheel spacers from JC Whitney to space the wheels out enough to clear the calipers. This caused the tires to rub the fenders on turns. I spoke to Pete Van Iderstine at Early Wheel to find out if their wheels would clear. Pete told me that all of the aftermarket wheel suppliers used the same centers and rims. He suggested grinding the Corvette calipers to clear the wheels. I ground and refit the wheels again and again until they seemed to clear, then went for a test ride. They still hit. So I ground and test drove several times until I didn't hear them squeaking. It was necessary to grind the bleeder on the back calipers so much that it was not possible to bleed the rear brakes. The rear tires still rubbed until I had the Corvette rear adjustment corrected. One of the rear wheels I had been using was an AG code 7" wide rally wheel. These were only used on Corvettes, and only in 1968. I finally found another one, had the two of them powder coated and installed them. I replaced the rear calipers at the same time. I used aftermarket rally wheels on the front. These have the same clearance problem as the solid wheels, so I am still looking for a pair of 15" x 6" GM rally wheels for the front.

Friday, October 2, 2009

Bronco Colors?

As soon as I got the coupe back to Denver, I started to talk to body shops and painters. I spoke to John May, one of the best, if not the best, street rod painters in the Denver area. I told him the car was to not going to be shown. I did not want a perfect paint job, or even perfect body work under the paint. I was looking for a car that I could drive to work and park in the mall, one that a friend calls a 50-50 car - it looks good at 50 yards or 50 miles per hour. I didn't want to worry about road scars. John seemed to get excited as I described the car. He said that the body and paint work would take ten to twelve months. I thought "John, you're not listening." When he mentioned a ten thousand dollar price tag, I said "You are really not listening to me, John.

I heard that a local collector with twenty or more cars had all of his cars painted at a Maaco shop in Aurora. I spoke to them and they estimated $1,700.00. Some body work and painting inside the trunk was added. The final cost was just over two thousand dollars, a cool eight thousand less than the next lowest estimate.

Minor modifications were made to the body. The lower chrome spear on the side of the hood was removed, along with the "cat whiskers" and Ford Deluxe logo above the grille. As mentioned before, 124 louvers were punched in the hood. The holes for the extremely ugly '39 trunk handle were filled and the Ford emblem between the handle and licence plate bracket was removed. A '40 Ford trunk handle / licence plate light from Bob Drake was used. This handle is still no masterpiece, but it's way better than the earlier piece. Bob Drake reproduction '40 Ford bumpers were used front and rear. The rear bumper has a Ford script cutout which acts as a third brake light. Wescott front and rear fiberglass fenders were used due to the poor condition of the original steel fenders.

From the day I got the Dartmouth Green stocker, I envisioned the future hot rod as black with flames fading from orange to yellow. When I looked at the color samples at Maaco, I fell in love with a 1996-7 Saturn color called purple poly or purple metallic depending on the year. Suzanne pointed out that if I didn't get the flames painted right away, I would probably be happier with purple than black. I didn't and I am. When we picked up the car, Suzanne looked at me and said "I've only seen that look on your face once before."

I had 15" station wagon wheels on the front and Corvette AG wheels on the back. They were painted Chevrolet engine orange. This color combination led some folks in the area to believe I had painted the car in Denver Bronco colors. But it's purple and orange, not blue and orange. Besides, I'm a Giants fan.

Sunday, September 14, 2008

Interference

When the engine was running, a ticking noise could be heard coming from under the valve covers. When the covers were removed, it became obvious that the rocker arms were hitting the top of the valve spring assembly. This was due to a combination of a unique (weird?) engine design and modifications which we made to the valve train to increase performance.



Unlike any other popular overhead valve engine, the ’53 to ’64 Buick engines had a rocker arrangement where the rockers met the pushrods on the outboard side of the head and the valves on the inboard side. Viewed from the side, the valve stem crossed the pushrod. This had several advantages: The valve placement was near the center of the head (like a Hemi), the engine was narrow for its displacement, and the engine had a lot of torque. Buick was so proud of the torque numbers that they used them to identify the engine instead of horsepower or displacement. The 340 horsepower 425 was called a Wildcat 465. The 360 horsepower two four barrel version was dubbed Super Wildcat 465.

However, the valve arrangement also had disadvantages. One of them is that the valve placement necessitated very small valves for the engine displacement, giving rise to the derisive term “Nailhead” to describe the engine. The rocker arms also have an angular configuration in two dimensions; viewed from the side and from above. There is very little clearance between the rocker arm and the valve spring assembly. In addition, the exhaust passages are long and tortuous, making these engines harder to cool than most.

Kenne-Bell used to be the go-to company for performance Buick parts. (They have since switched to Mustangs because very few performance Buicks are being built nowadays.)
Kenne-Bell valve springs for Buicks are larger in outside diameter than original Buick springs. This extra diameter exacerbates the rocker to spring clearance problem. The rocker arms must be hand filed to provide at least .030 clearance.

After the rocker arms were filed, the engine noise disappeared.

On March 16, 2001 the car was loaded on Passport Transport and shipped to Denver where I lived at that time. The car had spent four years and one day at Rustic.

Saturday, September 13, 2008

Disengagement (Part 1)

Except for temporary transportation units, I have never owned a vehicle with an automatic transmission. I was determined not to build one.

I talked to Darrell Shepher at 4 Speeds by Darrell about building an M-22. Because new gears, especially second gear, were getting rare, the cost would be $2,475 (In 1997!). I could save $1000 by using Italian gears. I asked what the difference was and Darrell said the Italian gears were not as strong. What is the sense of a rock crusher with weak gears? You might as well use a Super T-10. I ordered the transmission with GM gears. Darrell said he had a Doug Nash cast iron case for an M-22. The purists didn’t want it because it wasn’t original. He would use the cast iron case for the same price. Sold!

We used TCI under floor pedals with a ¾” bore clutch master cylinder and a remote reservoir for the clutch master. Quartermaster supplied a hydraulic throwout bearing. The clutch is a Centerforce Dual Friction unit for a 427 Corvette.

It took a long time to bleed the clutch the first time. The master cylinder began to leak after a few cycles.

A new ¾” master cylinder was ordered from TCI and installed. It also leaked.

A 1” master cylinder was ordered from TCI and installed. It bled much faster than the ¾” cylinders. Due to the lack of a pedal stop, the increased fluid flow blew out the seals in the throwout bearing.

The engine and transmission were removed from the car and separated. The throwout bearing was rebuilt with new seals and reinstalled. The engine and transmission were put back in the car. We went back to a ¾” master cylinder. The throwout bearing still leaked.

The engine and trans were removed again. The throwout bearing was disassembled. The O-rings looked good and there was no apparent damage to the metal parts. The Quartermaster distributor supplied a new throwout bearing which was bench tested and worked OK.

The engine and trans were reinstalled. The clutch system bled well but started to leak after a couple of cycles. The engine and transmission were removed for the third time. The outer O-ring was broken clear through at the top. The throwout bearing was rebuilt with new seals and reinstalled. After engine installation, the system was bled and cycled. No leaks appeared. An adjustable pedal stop was installed.

We reused the Hurst shifter which was on the old transmission. Shifting without the engine running, the linkage felt “crunchy” in first and second gear and “rubbery” in third and fourth.
With the engine running, the transmission would only shift into fourth gear. Several tries at adjustment finally resulted in the ability to shift into all gears, but it was well short of shifting well. The car moved under its own power on June 29, 1999.

Rustic replaced the shift tower with another that they had. There was a slight improvement, but the shifter was still tight. Did I want to buy a new shifter? No, I wanted them to try the old one again. It worked and seemed to shift OK.